
If you have a dripping tap and shower in the same house, you’re not unlucky — you’re looking at the same failure showing up in two places. Both a faucet and a shower valve stop water the exact same way: a moving part presses a rubber or ceramic seal against a metal seat. When that seal wears, hardens, or gets chewed up by mineral grit, water sneaks past and drips. The good news is that the repair is almost identical whether it’s the kitchen tap or the shower, and in most homes it costs under $15 in parts.
Below I’ll walk you through exactly why each one drips, how to tell which part failed, how to fix it step by step, and when the drip is actually a warning sign you shouldn’t ignore. I’ve repaired hundreds of these, and I’ll be straight with you about what’s a five-minute job and what isn’t.
What actually causes a dripping tap and shower — is it the same problem?
Yes, in about 80% of cases it’s the same problem: a worn seal inside the valve. A tap and a shower both use a control valve, and that valve has one job — to press something soft (a washer or a ceramic disc) against something hard (the valve seat) to make a watertight stop. When water keeps dripping after you’ve turned the handle firmly off, that seal is no longer sealing.
Here are the specific culprits, roughly in the order you’ll run into them:
- Worn rubber washer — the classic cause in older compression taps. The rubber flattens and cracks, so it can’t seal. Cheapest fix there is.
- Damaged or scaled ceramic cartridge — modern single-lever taps and mixer showers use a cartridge with ceramic discs. Hard-water grit scratches the discs and they weep.
- Corroded valve seat — the brass seat the washer presses against gets pitted, so even a new washer won’t seal on it.
- Perished O-rings — these cause drips around the base or handle rather than out of the spout, but people lump them in with a “dripping tap.”
- Too much water pressure — if your mains pressure is above about 80 psi, it forces water past seals that would otherwise hold. A pressure-reducing valve solves a whole-house dripping problem.
One thing to rule out early with a shower: a shower head that keeps dribbling for a minute or two after you turn it off is normal. That’s just water draining out of the head and the riser. A real drip keeps going, drop after drop, ten minutes later.
How do I know if it’s the washer or the cartridge?
Look at your handle and count how it moves. A tap you turn (rotate several times) to shut off is a compression tap with a washer. A single lever you push up/down and swing side to side is a cartridge or ceramic-disc tap. That one detail tells you which part to buy before you take anything apart.
Here’s the quick diagnostic breakdown I use:
| Symptom | Most likely cause | Part you need | Typical cost |
|---|---|---|---|
| Drips from spout, twist-handle tap | Worn rubber washer | Washer + jumper valve | $2–$5 |
| Drips from spout, single-lever tap | Scored ceramic cartridge | Replacement cartridge | $8–$25 |
| Drips even with a brand-new washer | Pitted valve seat | Seat + seat grinder, or reseating tool | $6–$15 |
| Water weeps around the handle base | Perished O-ring | O-ring kit | $3–$6 |
| Shower head drips long after shut-off | Failed shower cartridge/diverter | Shower cartridge | $10–$30 |
| Multiple fixtures drip at once | Excessive mains pressure | Pressure-reducing valve | $40–$90 |
If you’re staring at a single-handle kitchen tap specifically, we’ve got a dedicated deep-dive on that exact fixture — see our guide on how to fix a leaky kitchen faucet with one handle, which shows the cartridge pull step-by-step with the puller tool.
How do I fix a dripping tap myself, step by step?
Turn off the water, plug the drain, then pull the tap apart, replace the seal, and reassemble. Most people can do a washer or cartridge swap in 20–40 minutes with basic tools. Here’s the full sequence.
- Shut off the water. Close the isolation valve under the sink (a slotted screw you turn a quarter-turn with a flathead), or the main stopcock if there’s no local valve. Open the tap to release pressure and confirm the water’s actually off.
- Plug the drain. A dropped screw or washer down the plughole ruins your afternoon. Put the stopper in or lay a rag over the hole.
- Pop the handle cap and remove the handle. There’s usually a small hot/cold index cap you pry off with a fingernail or a flat screwdriver, hiding a retaining screw underneath.
- Unscrew the bonnet/retaining nut. Use an adjustable wrench. Wrap the jaws in tape or cloth if the finish is chrome or brushed gold so you don’t scratch it.
- Lift out the guts. On a compression tap you’ll see the spindle with the washer held by a small brass screw at the bottom. On a cartridge tap the whole cartridge lifts (or pulls) straight out — note its orientation, because ceramic cartridges only go back one way.
- Replace the worn part. Swap the washer (take the old one to the store to match the size — usually 1/2″ or 3/4″), or drop in the matching new cartridge. Smear a little silicone plumber’s grease on O-rings.
- Check the seat. Run a fingertip around the brass seat the washer presses on. If it feels rough or pitted, that’s why a new washer still drips — reface it with a cheap seat grinder or replace the seat.
- Reassemble and test. Reverse the steps, turn the water back on slowly, and watch for drips at both the spout and the handle. Don’t overtighten — crushing the seal causes leaks and makes the handle stiff.
If the drip is coming from around the handle rather than the spout, the fix is slightly different — you’re chasing O-rings and the stem seal. Our walkthrough on how to fix a leaking faucet handle without calling a plumber covers that exact scenario, and the faucet handle replacement parts guide lists every little component so you order the right kit the first time.
How do I stop a shower from dripping when the tap fix doesn’t apply?
A dripping shower is fixed the same way as a tap — replace the cartridge or washer inside the shower valve — but getting to it is a little different because the valve is buried in the wall behind a trim plate. Turn off the water, pop off the handle and the round escutcheon plate, and you’ll find the cartridge held by a clip or a retaining nut.
The catch with showers: mixer and pressure-balance valves use a specific cartridge that varies by brand, so bring the old one (or a clear photo plus the brand stamped on the trim) to match it. Force a generic cartridge in and you’ll get temperature swings or a fresh leak. While you’re in there, check the shower diverter too — if your drip is coming out of the tub spout while the shower runs, or the head dribbles because water isn’t fully diverting, the diverter is the real problem, not the valve seal.
A few shower-specific pointers:
- Take a phone photo before you remove anything — cartridge orientation and the hot/cold “keyway” matter.
- Descale the shower head separately. A head that spits or drips unevenly is often just clogged with limescale, not broken. A one-hour soak in white vinegar clears most of it.
- If your shower drips and the pressure feels weak, sort the pressure issue too — our guide on how to fix low water pressure in your shower head covers the clogs and flow restrictors that often show up alongside a worn valve.
Why does my tap or shower still drip after I replaced the washer?
Nine times out of ten, it’s because the valve seat is damaged. You put in a perfect new washer, but it’s pressing against a brass seat that’s pitted or scaled, so it can’t form a seal — like putting a fresh gasket on a warped surface. Run your finger or a cotton bud around the seat: if it snags or feels gritty, that’s your answer.
You’ve got two fixes. Reface the seat with a seat-grinding tool (a cheap tool that screws in where the tap guts sit and grinds the seat flat in a few turns), or unscrew and replace the seat entirely if it’s a removable type. On plenty of modern taps the seat is integral and non-replaceable — at that point, swapping the whole cartridge or the whole tap is the honest answer.
Other reasons a “fixed” tap keeps dripping:
- Wrong washer size or type — a flat washer where a coned one belongs, or a millimetre too small, and it won’t seat.
- Debris on the seal — a fleck of grit or old PTFE tape trapped under the new washer. Flush the line before reassembly.
- Overtightened handle — crushing a ceramic cartridge cracks it. Snug, not gorilla-tight.
- High pressure — if every fixture in the house weeps, test your mains pressure. Above 80 psi, fit a pressure-reducing valve and the drips often stop on their own.
When should I actually call a plumber instead of fixing it myself?
Call a plumber when the leak is behind the wall, when the valve body itself is cracked, or when you can’t isolate the water. Those are the jobs where a DIY attempt can turn a $10 drip into a flooded ceiling. Everything on the near side of the wall — washers, cartridges, O-rings, seats, aerators — is fair game for a confident DIYer.
Signs it’s time to hand it over:
- Water stains, bubbling paint, or damp spreading on the wall or ceiling below a shower — that’s a concealed pipe or valve-body leak.
- The shut-off valve won’t fully stop the water, or there’s no isolation valve and the stopcock is seized.
- You’ve replaced the cartridge and reseated the valve and it still drips — the valve body may be cracked and need cutting out.
- Corroded, seized fittings that won’t budge without heat or the risk of snapping a pipe.
Left alone, a slow drip isn’t harmless. A tap dripping once per second wastes roughly 3,000 gallons a year — enough for over 180 showers — and warm-side drips waste the energy you paid to heat that water. A shower drip behind the wall is worse, because it rots studs and grows mould you can’t see until the damage is done.
FAQ
How much does it cost to fix a dripping tap and shower?
If you DIY it, usually $5–$30 in parts total — a washer is a couple of dollars, a tap or shower cartridge is $8–$30. A plumber typically charges $100–$250 per fixture including the call-out, which is why a washer swap is one of the most worthwhile DIY jobs in the house.
Is a dripping tap and shower an emergency?
No, a visible drip from the spout or head is not an emergency — but don’t sit on it for months. It wastes thousands of gallons a year and a worn seal only gets worse. A leak behind the wall, showing as damp or stains, is urgent because of hidden water damage.
Can hard water cause both my tap and shower to drip?
Yes. Hard-water minerals scratch ceramic cartridge discs and build scale on valve seats, which is exactly why the same failure shows up at multiple fixtures around the same time. Descaling regularly and, if your water is very hard, fitting a softener extends the life of every seal in the house.
Why does my shower head keep dripping for minutes after I turn it off?
A short dribble for a minute or two is normal — it’s just water draining out of the head and riser pipe, not a leak. If it’s still dripping steadily ten minutes later, the shower valve cartridge has failed and needs replacing.
Do I need to turn off the whole house water to fix a dripping tap?
Usually not. Most sinks have an isolation valve on the supply line under them that you close with a flathead screwdriver, so only that tap loses water. For a shower without a local isolation valve, you’ll need the main stopcock. Always open the fixture afterward to bleed off pressure before you take it apart.
What tools do I need to fix a dripping tap and shower?
An adjustable wrench, a flathead and a Phillips screwdriver, a replacement washer or cartridge, silicone plumber’s grease, and PTFE tape cover almost every job. For a stubborn cartridge you may want a cartridge puller, and for a pitted seat a seat-grinding tool. That’s a kit well under $40 that fixes the problem for years.
A note from our team
This guide was written by the srsunrise fixtures team, drawing on hands-on bench testing of the compression, cartridge, and ceramic-disc valves we build and sell. srsunrise designs faucets, shower systems, and tub fixtures to international sealing and flow standards (including WaterSense-aligned flow rates and ceramic-disc cartridges rated for 500,000+ cycles), and we back our fixtures with a manufacturer warranty on the cartridge and finish. If you’d rather replace a tired, endlessly-dripping fixture than keep patching it, our engineers stress-test every valve seat before it ships — because the best fix for a chronic drip is a valve that was built to seal in the first place. For a broader look at what a good warranty actually covers, see our rundown of which faucet manufacturer has the best warranty in 2026.

